Ball and patch size for .577 enfield Shooters Forum . What size ball and patch should I be looking at? the best I can find is a .570 ball with a .018 patch. You'll have much better accuracy if you use the proper bullet in your Enfield. That being said, they were designed to use the Minnie Balls, conical, hollow-based bullets, not.
Ball and patch size for .577 enfield Shooters Forum from www.historicalimagebank.com
I started my .577 Musketoon off with .575" RB's and a 10 ounce denim patch that's .0225" thick. That particular Enfield's bore diameter measures .574", with grooves only.
Source: upload.wikimedia.org
If you wanted the absolute correct diameter minie ball, you'd have to slug the bore. Having said that, I think you would be safe in using a standard .58 minie. The mine ball should.
Source: saguaro-arms.com
While at a cartridge show year ago, I came across some loose .577 cal. Enfield bullets by E & A Ludlow, Birmingham, England. As can be seen in the photograph, they were.
Source: cdn2.imagearchive.com
I've shot a number of rifled muskets originals and repros the Enfield, Remington Zouave, Mississippi Rifle, '61 & 63 models and by far, the Enfield was my favorite. As Hawg.
Source: images.squarespace-cdn.com
Made to be held in a vise; with wooden dowel, push the bullet through the die to size it. Will also straighten the skirts if they are bent after casting. Each die is tapered inside for ease in starting.
Source: www.24hourcampfire.com
Euroarms barrels could be anywhere from .577 to .582. You want to use the minie that best fits your bore, usually one that is .001" or .002" below bore size. The gun shop you're.
Source: www.flecktarn.co.uk
Have you determined your bore size and the diameter of your Minie Balls? Ideally, for best accuracy, your Minies should be no less than 2 Thousands of an Inch undersize. If.
Source: thumbs.worthpoint.com
When I tested the bullets in the barrel (the size is marked as being .577 Caliber, .560 Diameter, 536 gr. hollow base), we have a good 16th of an inch play in the barrel (unlike.
Source: image.invaluable.com
A correct patch/ball combo should allow you to shove the ball down the bore without busting a gut. The fact is that a dead-soft lead ball will flatten at the rear and seal the.
Source: collegehillarsenal.com
I said I had never heard of patching a round ball in a rifle with a paper patch. Others chimed in and said they have been shooting them with good results for years. I.
Source: i1.wp.com
A .562 ball with a thin patch would load quickly and at short ranges should have good accuracy. You could even create paper cartridges, which would load easily with the.
Source: dygtyjqp7pi0m.cloudfront.net
It was common in the later war for the US to issue .574" (i.e. Enfield size) for both Springfields and Enfields, and the preferred combination was a .58 Springfield with Enfield sized .574" ammunition.
Source: thumbs.worthpoint.com
I've shot a number of rifled muskets originals and repros the Enfield, Remington Zouave, Mississippi Rifle, '61 & 63 models and by far, the Enfield was my favorite. As Hawg.
Source: www.snaphaunce.com
I have a parker hale .577 three band musket. Although I would normally shoot minis in it, I find some of the gun stores around my area don't stock my size...
Source: cdn2.imagearchive.com
I have a 2 band Enfield which I shoot happily at 100yards with a 600ish grain minie and abit of black, but I would also like to shoot the rifle on my smaller club gallery range.
Post a Comment